ECOVACS 7 Series Guide de l'utilisateur

7 Series User GuideRobot Vacuum Cleaner

autoedgespotretur nintensive2.Cont e n t ( For D73)Main UnitCharging block Virtual wall Battery for virtual wallUser Guide Border tapeMagnetic adding

12VEnj o y Sma r ter L i fe!DC12V AC220-240VDC14.5V50Hz30W1.0ADC3VDC3V≤5meters30W0.25m/s0.7L≤60dBAbout 3 hoursAbout 60 minutes2120-150M330×330×100mm

2.Content(For D76)Main UnitTechnique parameter( For D76)Charge stationRated powerspeedDust capacityNoiseCharging timeWorking time per chargeCieaning a

3.Parts Description(For D73)13control buttonwind gaterotating side brushAll-round wheelsuspendeddriving wheelrubber scraperon/off switchdust sensordus

Handheld vacuum cleaner Main Unit is the same as D73Charge station ( Front view)Dust container power slotInfrared signal generatorCharging station pow

1. Power 7. Demo mode 13. Keep timing cleaning 19. Battery display2. Model selection 8. Border cleaning mode 14. One-time timing cleaning 20. Tip

Tangle the power cord on the pothook and do not scatter it besides the block or hold it under the base, in case that robot would get impeded when it t

● Press the key on host and get power supply. There would be a short music tip and at the same time LCD lights for roughly 2 second and goes off

Put the robot on the charging block and keep it charging after finishing house cleaning. Do not keep the robot on pause status for long time, b

This mode is applicable to certain area with plenty of dust.Under common circumstance, the cycle of one fixed point cleaning takes around 2 minutes

7.Automatically charging● ● ● ● ● ● When it finishes cleaning or there is low battery, it would seek charger in same route as automatic cleaning.To ma

Second time setting1. Now, the label high light, and the number with time setting is flashing.2. Set hourandminute via and , each time p

Note:Tips:When power is off, robot will not start work on appointment time .If you have already set appointment timing cleaning, please turn on the ro

10.Remote ControlTips:Battery placementIt applies two units of alkaline batteries (7#)Please note the positive and negative when place the batteryChan

Note:When you use virtual wall, please face marked ECOVACS to the block area you expect. Put virtual wall outside of the room you want to block to get

12.Border TapeUsage of Border TapeBorder Tape is used to confine the cleaning area. will not proceed beyond the border, allowing to

13.Day-to-day storageYou should keep robot stay at charger even though it finishes charging and cleaning task, because it will change to small currenc

15.Handheld vacuum cleaner ( For D76)Assemble the handheld vacuum cleanerAttention: Press the “ Handheld vacuum cleaner releasing button “ on the back

16.MaintenanceThe Main Unit CleaningDust box cleaningTurn off the power before cleaning the host.Draw out the plug of charger before cleaning the bloc

17Tips：If the dust box is not placed back or not properly placed, robot will alarm and show red indicator, will show on the LCD.141516Hold the

Thanks for purchasing products Hope you can enjoy itThanks again for your choice! patented . ! Rob

Main brush cleaningTips: Clean the main brush after it has operated for 4 or 5 recycles.Undo the screw fixed on the main brush.Remove the hair and dus

31Dust container cleaningDust container assembly Filtration cleaningPress the “Handheld vacuum cleaner releasing button”on the back of Charging Statio

Tap the filtration assembly gently to get rid of the attached dust.Take the sponge out of the filtration assembly.If needed , the filtration assembly

Note：Note:Side brush cleaningreplace sidebrushDriving wheel cleaningUp-ground height sensor cleaningPlease replace the side brush when it is destroyed

Dust sensor cleaningThe dust sensor is located at the front of dust entrance. It is able to detect the concentration of dust so that it can choose eff

17.Alarm functionNote:The robot will stop working under following circumstance; there will be alarm and tip sound at the same time. What's more,

36432118.Common FailureNo. Problem SolutionRobot keeps proceeding or moving backward once power is on.Turn off the power.1. Check if there is dust on

5619.Other ProblemsThere is much noise when the robot works.Press the ” emo mode and themachine does not react“ DTurn off the power supply, an

...cleaned for long time, as it is tangled with automatic and border cleaning mode. Its much hair and dust. side brush can r

21 How does main brush avoid being tangled 26. by power cord? Answer: Robot is probably get tangled by the wire scattered on the floor when i

E n j o y S m a r t e r L i f e !D7S-000IM2011/02

1. Safety Instruction... 10.Remote Control... ...User Guide... .Power

1.Safety InstructionThe User GuidePlease conform to the basic safety precautions as follows:● Read the content in this user guide carefully and insta

The Spectrum of the Product Use● This robot is applicable to domestic sweeping, including wooden floor, rubber floor, ceramic tile, linoleum and mediu

Notes before Cleaning● Take extra care of the robot when the first it works. Please remove the obstacles when it is beyond the robot. Try to avoid the

● Take good care of the product and keep it beyond child and people who can not judge danger nearby. Extra attention should be paid when it starts wor